Glock Barrel Wear - Attached are pictures of wear marks on the barrel. I just put 150 rounds of factory 115gr FMJ in the G19. For me, there are already signs of packaging, especially on the front of the lid, as well as the glue if desired. Before I put in the rounds, I did a field infusion that cleaned and lubricated. It has also been cleaned and waxed after several different trips.
This seems excessive to me. I have not seen this wear before on my new guns (Sig, HK, used G26 and others. Is this normal? Your feedback would be appreciated.
Glock Barrel Wear
The wear you put on the barrel for the first hundred rounds is usually what you will get. In other words, it won't last the life of the gun, the wear you'll get happens faster.
True Precision Match Grade X Fluted Barrel For Glock 26
Is it Gen5? From what I've seen, they tend to wear more than previous generations probably due to hard tolerances. The barrel cap wear is more than a few G19 Gen5s I've seen, but not the barrel itself. If you don't have a functional problem, it's not an aesthetic problem. The metal protection is deeper than the end, so you don't have to worry about that.
I bought new tires the other day. 150 miles later and the little rubber is leaking, only where the rubber meets the road, though. I have to worry
Thanks for the comments. It's a Gen 4 that I bought new a few weeks ago. As I mentioned earlier, I have not had these signs of wear on my new Sigs or even the pistols I have purchased slightly used. (Just look at my current port of Sig 938 that has over 600 rds with no lock, cap or barrel). I think Glock will put a durable finish on the barrels.
I just talked to the Glock gurus and they help me not to worry as it is normal. Still not happy with the early wear
Best Glock Barrels [2020]: How To Choose & Top Picks
The guard said: I just talked to the Glock gurus and they help me not to worry because it's normal. Still not happy with the early wear Click to enlarge You won't get tired of it. It is self-control. You can't see when you shoot. It is not sustainable.
Common and variable between different Glocks is how the barrels fit the pictures such as metal and metal touch. Your Glock has a better (harder) barrel than the other guns you mentioned, good stuff.
MikeLadner said: I bought new tires the other day. 150 miles later and the little rubber is leaking, only where the rubber meets the road, though. I have to worry Click to expand... boo hoo, not right.
I think it is difficult. Last night at the club we were supposed to practice IDPA, but since only 4 people showed up, we tried something different. We set up a 6" iron plate and started at 25' and went to 170' in about 30' increments. The short distance was easy, but as we got further out, it was hard to hit. I enjoyed hitting 170.'' after only 2 shots i have to attribute some of that to the tight barrel fit!!
New G19 Barrel Wear
The watchman said: I think it's difficult. Last night at the club we were supposed to practice IDPA, but since only 4 people showed up, we tried something different. We put on a 6" steel plate and started at 25' and went to 170' in about 30' increments. The short distance was easy, but as we got further out, it was hard to hit. I enjoyed hitting 170.' distance after only 2 shots. I have to attribute some of the barrel fit!! Click to expand... And more importantly, the shooting skill.
True, but at 74, my arms are not as strong as they used to be!!! Of course the good vision of Tru-Glo made it easier too!!
If nothing changes in the gun, then the wear that occurs in the first few hundred rounds is all the wear that will occur.
When you say "I wish it hadn't happened sooner" you're basically saying "I wish it hadn't happened yet."
Original Marui Glock 19 Slide, Outer Barrel And Recoil Guide Rod
What happens if the metal parts are very hard and rub hard to reduce each other, then some metal will come out. The end will follow. When enough material has been removed from the parts to fit better, the material is done removing - done, no more needed. If nothing else changes, you can go back after 10,000 cycles and it will look the same.
Sometimes the coating can be a little thick and you will only have some wear on the coating that comes down to the metal. But if it is attached to the metal that needs it, it will not have enough insulation.
Here are pictures of the Sig M11-A1 after 2000 rds and the HK P30SK after 600 rds. Not worn Sig and a little about the tip of the barrel. None of these manufacturers have a good finish or Glock does. Which one?
Mtstream said: Are my posts hard to understand? Click to expand... Nothing more than mine, but a lot of Glock people can't see the "all" "all" "all" fog.
Mark On My Barrel?
I have many concerns, but this is not one of them. I tend to shoot and enjoy my guns. If they break or wear I have a new part or the whole gun. So far I have replaced 2 manufacturers on my ruger and 10/22 pistol
Everyone's writing is clear. I was just pointing out that other gun manufacturers don't seem to show the ear like the Glock is all about. I will continue to record them all and enjoy them.
If the gun has an A part that is 2" and a B part that is 1", we call it an additive tolerance - the gun still works, but it's too close to the edge and the parts have to fit together to actually fit. . So you have fabric and fabric.
IF, by fate, you got a different G19 than you did where the parts were at the same end of the tolerance range and you got a SIG where the parts were at opposite ends of the tolerances, you'd be having exactly the same conversation. on the Sig forum instead here.
G19 Gen5 Wear
By the way: I will say one thing SIG. Their high end pistols (usually) have tighter tolerances than Glocks. This helps prevent problems like this (it helps, but it still happens), and it's also why a gun costs twice as much for similar reliability/performance.
The only way to prevent the barrel from behaving this way is to lock it in a safe place where it won't be fired again, and don't tamper with it.
The E series G27 and G26 (both have the antique finish that many enthusiasts want) show lots of light "ringed" spots and scratches on the finish, similar to what some enthusiasts and owners have. met with. complaining about new Glocks. The barrel is not actually closed of course (nitrocarburized on the top surface) but there are many closed spots on the end covering the metal surface. (Older gun grades we're told may have different finishes, but they were one type or another of the basic black phosphorous finish, depending on what the company was doing at the time.)
Of course, each of these sub-par Glocks has been used to fire over 17+K since I've owned them, but barrel wear hasn't changed much in that time. They looked pretty good after the first case or two of ammo I shot through them.
Shavings From Casing Left On The Side Of The Barrel. Glock 17, Probably 7k Rounds Through It. Original Everything Including Recoil Spring. Shot All Kinda Of 9mm Through It. Mostly Brass Though
Of course, I also keep the outside of my barrel very thin, to reduce the expected friction that occurs between the surface of the muzzle and the surface of the barrel. A little oil can help reduce the friction that normally occurs between moving metal surfaces. Rub a drop of regular oil around the barrel.
I haven't tested any of the new PVD finishes on the Glock, but I have them on several revolvers (mainly the cylinder). It's a durable finish, meaning it's more durable than a regular phosphor finish, and definitely a blue finish, but it still shows wear over time (and scratches, scuffs, etc.).
Here is the G19 Gen 4 barrel after 2000 rounds. Just spit it in the barrel and call it good
Glock threaded barrel protector, glock 20 conversion barrel, glock 17l threaded barrel, glock threaded barrel, glock wear, glock 35 conversion barrel, double diamond glock barrel review, glock conversion barrel, lone wolf glock conversion barrel, glock 30 threaded barrel, polishing glock barrel, lone wolf glock 21 barrel